New Profile Posts

  1. dave-396
  2. Tha Jimmer
    Tha Jimmer
    What up Lil Honda!!! I have had this Ct70 for decades. It has gotten beat but now it is time to bring Frankenstein back to life!!!
  3. Donald_50
    Donald_50 scooter
    I am interested in "Picking your brain" regarding rear shocks.
    I have 2 CT-70's, and I live in North San Diego County, CA.!
    (Vista, CA 92084)
    My question, if I find a pair of "Old" used, Ohlins with the "Piggy-Back" reserviors, 14..
    14 and 1/2 inches "Eye to Eye",
    And then have YOU or a bike shop here in North San Diego County, CA rebuild them...

    Thanks for your time...
    Cheers, Donald_50
    Vista, CA 92084
    1. scooter likes this.
    2. Donald_50
      Thanks for your reply...
      Ohlins are the Most popular suspension (Front & Rear), for any and all bikes today!
      Ohlins are made in Sweden, and cost starts around $1200.00 and go up from there.
      I mentioned "Old, Used" because I really don't want to spend 2...5 Thousand on these!
      There are many videos on "YouTube" regarding Ohlins Rear Shocks.
      Feb 27, 2018
  4. JRuw91
    JRuw91 racerx
    What’s the difference between a Dax seat and Ct70 Ko seat? I’m looking to get a kepspeed Dax leather lower profile seat for my Ct70. The only place I can find one is is from the UK so I wanted to make darn sure it would fit before I ordered it. They mentioned the locking mechanism on the seat was different. Key instead of leather.
  5. JRuw91
    JRuw91 racerx
    What would be the best way to go about taking off and replacing the decals on the frame of Ct70 Ko? Just the Honda decals I want replaced.
    1. racerx
      Gentle heat, no more than ~125F, and a LOT of patience. Start at one end, lift & pull...slowly. Most of the adhesive should stick the the old decal. roll what remains, using your fingers. Cleaner formula paste wax is a safe means of dissolving the last of the adhesive residue. Wash the area with detergent & water, to strip the paste wax, in preparation for the new decals.
      Jan 13, 2018
  6. David Albright
    David Albright racerx
    My first project K2 70 bought partially disassembled handle bar seems to be original but there are no perches for the brakes, also came with a couple different on off switches and light switches can't find a photo of what is supposed to be there, schematics show there should be perches for brake?
  7. Will64
    Will64 red69
    Hi Bob,
    I'm restoring a 64 S90 and have been following your posts on the Yahoo site (with difficulty) . I would like to purchase a face plate and Denso or Nippon Seiki overlay if you still have them available. My gauge did not have the outer one and there aren't any identifying markings on the case. Is there a way to tell which is which? My email is Thanks, Bill
  8. Bad Dax
    Bad Dax
    Hi im looking at a ct70 hko but the engine number starts with st70e its an original bike with original engine does this sound correct,
  9. tjcin
    tjcin scooter
    Do you still restore shocks? I have a set I would like done. Thanks tjcin
  10. Roadrash
    Roadrash Darthvader
    What part of Kansas are you from?
  11. vintagehondatrailbikes
    vintagehondatrailbikes kirrbby
    Hi Kirrbby, I received the eBay stuff. Thanks!
    I am wondering if you have any H K1 engines or numbers side cases? I'm looking for a 203284 or something close.
    Let me know.
  12. Roadrash
    Roadrash kirrbby
    Kirb, I just picked up a 1970 CT70 that needs some attention and I really don't know where to start, do you recommend getting a repair manual? I was told it ran a couple years ago but it definitely looks like it has some wiring issues.
  13. vbwstripes
    vbwstripes 574hondarider07
    Hi I was wondering if you could send me a picture of the shocks? My email is

    Also, how much were you looking for for the shocks and tubes?
  14. gregkcheeseburger
    gregkcheeseburger racerx
    Hi Bob,I hope you can answer a question,im putting together a 76 CT70 and the motor was apart,the transmission is intact but there are no thrust washers or spacers on ends of trans shafts,If I remember each shaft has a copper washer and theres one spacer,I cant find any of the parts dealers that have these in stock
  15. joshmedley88
    Little by little this little gem is coming along nicely. Just love vintage Honda motorcycles so nostalgic and bulletproof machine's
  16. Cleato904
    Cleato904 mikesminitrail
    Look under the wanted ads and look at the pictures I posted of the cover it's yellow
  17. Cleato904
    Cleato904 mikesminitrail $70 total amount.
  18. cbryder
  19. FFFergie
    I need good places to buy parts and advice on powder coating vs paint. What is good to remove rust and polish up the wheels ect. Thanks!
  20. Enginedoctor