Search results

  1. hrc200x

    Cracked Engine Case… best repair?

    Is it for sure a crack? Sometimes the casting lines can look like cracks. If you can verify it isn't leaking oil I wouldn't touch it.
  2. hrc200x

    Honda CT70H Fuse Blows

    Could be wrong ignition switch, if there is a blue wire in the ignition switch wires that's for a k0 and would blow fuses. Your bike has a speedo that's separate from the headlight correct?
  3. hrc200x

    Clutch adjustment screw will not tighten

    Does the clutch seem to be working when riding? You might want bike laying on its left side when doing this because some parts will fall off if its standing up. Make sure 10 and 11 are accounted for when reinstalling as thats the oil passage to the end of the crank to lube the primary gear...
  4. hrc200x

    Thread pitch and diameter for idle and air jet screws?

    Thank you both for info. So this might do it: https://www.amazon.com/0-75-Taper-Plug-0-75mm-Pitch/dp/B06W5H82YV
  5. hrc200x

    Thread pitch and diameter for idle and air jet screws?

    Tried a quick search on here before the original posting and didn't find anything, but I usually don't have any luck with searching. Wonder if there is a tap made in whatever size these jets are.
  6. hrc200x

    Thread pitch and diameter for idle and air jet screws?

    Is there anyway to clean up the threads on the carb body for the idle and pilot air jet holes? These are the holes on the outside of the carb. Have a air screw that threads in a few threads then gets hard. Already had it in a sonic cleaner so don't think it's junk that's removable that's causing...
  7. hrc200x

    "Scooter" rear shock rebuild

    Nice work, hard to believe how well some things clean up. After your done with a rebuild do the shocks have some oil dampening?
  8. hrc200x

    Is anyone still using eBay?

    Has anyone that's sold over 600 worth of stuff on eBay gotten a tax statement or did they decide to not send one out?
  9. hrc200x

    New Honda throttle pipe/grip came off

    Kirrbby, did your bad ones come off or bind?
  10. hrc200x

    New Honda throttle pipe/grip came off

    Mechanically fixed up a z50 k3 couple months ago and while test driving it the grip with throttle pipe inside came off. It was all new throttle parts from Honda (throttle pipe, throttle hinge, cable holder, stopper, and screw). I believe the handle bar to be the original. Thinking what could...
  11. hrc200x

    Is anyone still using eBay?

    That are many things that have made ebay not what it used to be. Remember the days when a search for Honda ct70 would turn up 3 pages of results, now it's 10,000+ results because of listings like generic mirrors or saddle bags. Have you noticed if you have buy it now listings that renew...
  12. hrc200x

    Ct70 ct70H brake lever info

    Didn't some cables have a different size barrel on the end of them. Do the different levers have a different size hole the barrel fits in?
  13. hrc200x

    z50 k3 head with stamping C3

    I'm interested. I'll send a pm. Thanks
  14. hrc200x

    Carb leak

    Fuel filter cover plates can warp over time. Could it have the wrong o ring? Stripped threads in the bowl is common. Clean off the corrosion and you can try different o rings, tightening the screws more but be careful not to strip threads. If desperate to ride maybe a small C clamp from one side...
  15. hrc200x

    Tranny problems

    I like vesrah brand gaskets but if i recall they had a run and maybe still do that one of the oil pump paper gaskets seems to be made to thin and made the oil pump bind. Which ever brand kit you get, if you install the oil pump gaskets better make sure it spins easy by hand after the phillips...
  16. hrc200x

    Too many junk carbs

    Maybe some z50 middle lower left. If any have a high altitute adjustment knob and look like ct carbs from KO-77 they might be US90, trail 90, st90.
  17. hrc200x

    Too many junk carbs

    I sent you a message. I'd be interested in them
  18. hrc200x

    z50 k3 head with stamping C3

    Thanks Kirrbby, another K3 z50 I seen had the same C3 head so thought it may be popular on the k3's.
  19. hrc200x

    z50 k3 head with stamping C3

    Looking for a good z50 head with stamping C3. Working on a k3 z50 so those models should have that head. Needs to be complete with cam, valves, rockers.
  20. hrc200x

    z50 k3-78 muffler or diffuser and rear brake panel, 69-71 z50 headlight glass & frame muffler guards in yellow, blue, red

    Looking for the diffuser that goes in the end of the pipe on a k3 z50. k3-78 should all be the same, would buy complete muffler if have to. Rear brake panel with splined brake shaft and brake arm. Also looking for the muffler guards that bolt to the frame on the right side below the seat on...
Top