Search results

Going to pull the trigger on a Lifan soon, either 125cc or 140cc. eBay is just shy of $300 and Amazon is $305. I could have swore they were closer to $225-$250. Where are you guys purchasing them from?

I know many of the members here have tried this kit: http://www.ebay.com/itm/HONDA-CT70-ATC70-SS50-Z50-XL70-CDI-Electronic-Ignition-Free-Postage-Included-/360940998284?hash=item5409c28e8c:g:2qUAAOxyhS9TfchT&vxp=mtr Over 200 have sold in the last couple months so I'd assume there are a couple...

Hi, I just pulled my 72 HK1 out of storage because of the nice weather up here in WI. I filled the gas tank, checked oil, etc. and it fired up on the second kick. I let it sit for 30 seconds or so, when a small oil leak started. I thought it may have been from when I checked the oil, so I put it...

I'll try to describe this as best as I can. Another case of the "I loaned my bike to a friend and now it has so-and-so problems." The trail he was on is fairly small, not exceeding 20 mph or so. By the way, he sucks at driving manual if that matters. Anywho, he returned it, and simply said "it...

1974 Honda CT-70 K3 Thought I'd post this, for any of you in the Milwaukee area.

I recently got a 1974 Ct70 project. Got her running the next day and noticed a few problems. I have tried two carbs, and the bike will run with either. The OEM one will be getting a rebuild soon. Anyways, when the bike is stopped, I can rev the motor up fairly high. I then shift into first, and...

Recently got another CT70, and I just got her running. There was a small oil leak coming from the top end, so I suspect it is the timing/cam cover. There is a small crack in it, so it seems likely that's the cause. All the ones on ebay are around retail for a used one, so I'd rather take a shot...

Finally got my HK1 running after rebuilding the transmission and carb. Today I took her out for 2-3 hours on a local dirt trail. I was washing it off (covered in mud) while it was running. I shielded the air intake, exhaust, etc. so no water would enter the engine. When I was washing the chunks...

Can someone tell me if there is a circlip that goes on the left shaft (one with the screwdriver pointed at it)? The shaft has a recess in it like where they normally go, but the diagram does not show one. I can only find one, and it gets installed later with the clutch. Also, while...

Anybody know the Honda part number for this? Looking to order one through a dealer and can't find it. COMPLETE GASKET_SET_FIT'S SEMI_AUTO_CLUTCH 50'S_70'S WITH/52/54MM_BORE (MOST_88/95CC) (MANUAL_CLUTCH_READ) (1004D)

Well, I haven't been into these little bikes for a year or two and it feels like forever. I have been all tied up with moving and other hobbies. Unfortunately a lack of time and extra moola has left my bikes sitting in the garage in need of repair and maintenance. My HK1 happened to take a...

Got a bunch of parts left from the HK1 I parted out. I am just going to list a few of the better parts in this new thread. Prices are not including shipping. If it is smaller I will put in a flat rate box or envelope ($5 or less). If it is bigger just message me with your zip code and I will get...

I recently acquired a repainted HK1 through a trade. The traded item was worth about $200 so that is pretty much what I have into it. Almost all parts are here except the engine and a few misc parts. The headlight and tail light are very rusty so they are not usable. Pictured are the main parts...

Im stripping down one of my motors to rebuild, and I thought about putting a racing cam in it. I have a stock bottom end but the top end was rebuilt with an 88cc big bore kit. Which cam should I use? Im looking for a little more power/speed. Links and input are helpful. Thanks

Alright, So I have been searching for a rebuilt bottem end for my '72 HK1. Someone on the local craigslist posted an H model that had a completely rebuilt engine, repainted frame, forks, powder coated rims with new tires and tubes, etc. I would essentially be taking the bottom end off and...

For sale I have an original CT70 HK1 air box and gas tank bracket. Both are in good condition. No rust or big marks on either. No pitting on the chrome end caps. Moving soon and trying to get rid of all my non-used stuff. $30 shipped for both. PM if interested.

Up for sale is my 1972 Model ('71 on the vin tag) HK1. 4 speed manual. Runs strong and starts first kick. Drips a small bit of oil from the oil drain bolt. I have done alot of work on this bike. I got it in 2008 as a barn find and stripped it down to the frame. Built it up again, cleaning it as...

Well I dont really know how to start... But today I found a decent crack in the engine block near the drain bolt. It has a 88cc big bore and a couple upgrades. Basically it wont hold oil and I dont know the options I have. I didnt want to buy an engine for $300. Plus then I would have to...

Honda ct70 trail 70 turn signals flashers OEM | eBay

Sold