So, I bought a Chinese knockoff and boy am I sorry

lowcountryearl

New Member
I bought Chinese knock-offs valve tappet covers described to fit my 72 CT 70 off of EBay, well didn't pay attention that the threads were longer than what I took off. End result was the longer threads prevented the intake valve adjustment screw to move properly and now I have no compression with the poor mans compression test.
The intake valve was way out of adjustment and I had just adjusted the valves a month ago. I suspect,,that may have broke the valve stem, maybe the spring IDK.
How would you approach this problem?
 
Don't think the aftermarket cover was the problem. They are made for a similar bike. You must have adjusted the valve incorrectly. The cover is a very lightweight THIN aluminum. It would be very hard to break the valve with the soft aluminum cover. There is a good chance that by setting the valve timing wrong, you bent the valve by doing so. Time to remove the head and rebuilt it. Cheap ebay/amazon heads will not work on a K1. All the sellers think their heads work on all years and that is not true. They ONLY work on 1982 and up. :LOL: Dratv has a E22 head on his site, if you do not want to rebuild it.
 
Rode the bike around for a good while after valve adjustment, here's a picture of the covers after trying to start the bike
 

Attachments

  • 20220213_221420.jpg
    20220213_221420.jpg
    1.1 MB · Views: 92
  • 20220213_221411.jpg
    20220213_221411.jpg
    1 MB · Views: 103
That's the only thing I did between the bike running fine and not running at all, I've set a few valve clearances in the past, feel pretty good they were set properly
 
A Honda tappet cover only has 4 threads showing with rubber o-ring installed, yours looks to be about 8. That china cover is way too deep letting the rocker chew it up and now you have a chunk stuck in the valve holding it open, time to tear that head down.
 
That sucks man! This repair is a perfect job for a leakdown tester to diagnose before tearing it down. Detects cylinder/valve leakage. If you have access to one, it will tell you exactly if the valves are bent and not sealing. If you hear air out the exhaust or carb, then you have an audible indication of bent or leaking valves. That said, severely leaking valves will not tell you cylinder or ring wear until you get the valves sealed up, but at least you'll know more before going into the motor.

Attached photo of a typical leakdown tester. Screenshot_20220214-221508_Amazon Shopping.jpg
 
Last edited:
Cheap ebay/amazon heads will not work on a K1. All the sellers think their heads work on all years and that is not true.
Doesn't the E8 marking on his head show that it's a OEM head? A good lesson is one that's taught over and over here- don't buy ebay or Amazon parts.
 
One thing to check is if a piece of aluminum is lodged between the rocker and the head keeping the valve from seating. That's easy to do before you disassemble
 
Think old CT was saying if he doesn't rebuild/ remove obstruction don't buy those cheap heads as replacement as their all for newer models with flat pistons
 
@Gary I can't see a piece lodged with just the tappet cover off, what would I need to take off to take a good look at that before a head removal.
I do want to keep this head as it is the original head from what I can tell so may buy the E22 head from Dratv and work on rebuilding the original
 
The picture confirms where the rocker hit in the ''extra threaded'' area. I have never seen that type of tappet cover but it's good to know and to let others know not to use them. Looks like a bunch of aluminum all munched up in the head. Not good.
 
Well, I tore it down this evening and the problem is a bent valve stem. These valves have "Japan" marked on them. Does anyone know where I can get another made in Japan valve. I am very gun shy of "made in China" at this moment.
 
Well, I tore it down this evening and the problem is a bent valve stem. These valves have "Japan" marked on them. Does anyone know where I can get another made in Japan valve. I am very gun shy of "made in China" at this moment.
Dr.Atv has Japanese valves. Or ebay is an option for OEM Honda valves. The exhaust valves are expensive but if you need it...you need it!
 
They are a pressed in "interference" fit. Although I don't believe they are extremely tight. Care should be taken to not damage the valve guide bore in the head when removing them. They make special valve guide punches that you can drift them out with. But new replacement guides need to be reamed to size inside(ID) with special valve guide reaming mandrels. Honestly, this kind of work is best left to a reputable engine machine shop as the cost for them to do the work will likely be far less than sourcing the proper tools to attempt a DIY repair. Gather your required parts and leave the rest for the properly equipped machine shop. I'd recommend having the valve seats dressed too if you're going that far.
 
I was just thinking that the bent valve stem may have damaged the guide,doesn't look damaged but...
I did order the OEM intake valve from Dratv, I guess I could put it in, re-assemble and do a compression check to see.
 
Well, found a OEM valve at the local Honda dealership, that was a stroke of luck, lapped it in and put it back together, compression is 120 psi.
Was hoping for a little more but all the internals look original so pretty happy with that. Lesson number 10233.09 never buy Chinese junk off of eBay
 
Back
Top