Search results

Show quality engine guard. Properly restored and triple chromed with an initial strike of nickel beneath the layers of copper. The plate section has been textured to replicate the stippled original finish. Never been on a bike. $225. PM if interested.

There have been a bunch of threads and posts regarding sprocket sizes lately. I understand how the sprocket calculators work, but I don't understand the discussions and calculations on mph/1000 rpm and optimizing sprocket setups using that information. And how can you do it anyways if the bikes...

Searched, but didn't find an answer to my question. Just how exactly does the clutch adjustment screw inside the clutch cover on a 4 speed work? The service manual says to turn it in until resistance is felt and then back it off a quarter turn. My bike still seems to jump into first gear a...

Why does the K1/HK1 headlight bucket have two holes in the back? Why does the head cover have three acorn nuts and one hex nut?

Does the speedometer cable need to be lubricated with grease, or can it be lubed with teflon like the other cables? Thanks.

Never seen one of these before. Cool looking bike. Called a Motra.

Anyone try the mud flaps that DRATV sells in a CT70 front fender? Just wondering if it will clear the head. The photos on the site show it on a dax low mount fender.

Anybody know if the dimmer switch TB sells with the gray cable for the K0 model will work on an HK1? I'm also looking at their brake pedal that says it's for a K0 and I need one for my HK1. Saw another pedal on DRATV, but the site states it's for auto transmissions only. Can't figure out how...

If you've got a flywheel for a 4 speed Hitachi laying around that has a points cam in good condition, let me know. Thanks.

Brand new. Never been installed. Has some surface imperfections as shown. $15 including shipping.

Why were the H models fitted with 14/45 sprockets and the 3 speeds with 15/38's?

Anyone have any experience with these carbs? eBay - New & used electronics, cars, apparel, collectibles, sporting goods & more at low prices The price is great, but I'd like to know if they're relatively easy to tune and reliable. Thanks.

Few questions. Does the wiring harness run under the fuel tank or beside it? Where do the two fuel tank pads go? Also, the big grommet that goes in the fuel tank bracket has a thick edge and a thin edge. Which edge faces up? Thanks much,

So here's what my stator looks like after I cleaned it up. Has anyone tried the 4-speed stator rebuild kit from CHP? It appears to come complete. Just screw it on to the stator plate Or is it better just to replace the points and condenser? Here's what my neutral switch looks like. It...

The inside of my flywheel was rusty so I took the parts out and cleaned them and the inside of the flywheel. I figured my trusty parts manual would show me how to put it all back together. Nada. Not shown. So now I have these parts and I'm unsure how to put them back in. Anyone know how or have...

I pounded out the old races in preparation to install the tapered steering races. I picked them up a couple of years ago from DR ATV. They're not the All Balls bearings. I measured the depth from the top edge of the steering tube to the ledge where the race sits. The new race is about 2mm taller...

A reintroduction: A couple of years ago in September, I was lucky enough to find an HK1 in fantastic shape. Strong engine, great body. Only a tiny dent in one of the upper fork covers. I started a thread on the forums here: http://lilhonda.com/webboard/f36/new-member-new-bike-7009/...

There are three cushions or grommets that the tail light bracket on a CT70 K1 or HK1 needs to mount the bracket to the fender. They're not available from Honda anymore. Does anyone know if the cushions still available for the K0 or the Z50's are similar enough to work in place of the original...

I bought this bike in September 2009 with the intention of restoring it. It was in great shape and ran fine. Since then it has been completely disassembled and cleaned. It has a title. The decals have been removed from the frame. Wheels have been rebuilt with new tires and correct cloud...

Sorry, it's not a dimmer switch, it's a switch assembly that has the turn signal and horn. I recently picked up this switch for a CT70 K1, K2, or K3. I bought it because I thought it would fit my HK1, but it is not the right switch. The Honda part number is: 35300-098-951. It's in perfect...