Search results

Hellro, I have a 73 ct70 3speed auto, when i am in 2nd gear it will slip in and out of gear when it is under a load or not. It is not a stripped gear or a slipping clutch, it feels like the clutch engages the disengages. The clutch is great and it does not do it in 1st or 3rd...

I am selling my CT70 to pay for my new boat engine (ugh), Its in very good cond starts right up and shifts smooth. Located in Western Mass. Zip 01030, $800 Pics available sale-fw6ea-2313441902@craigslist.org 1973 Honda CT70 Cell (413) 657-3415. Thanks, Fran

Hello Ct70 drivers, I am relisting my CT due to a buyer backing out, It has been cleaned up, new tire, tubes, cylinder& Piston, Carb ect. I have all the original parts to go with it then some extra's. The bike is orange and in good condition, Speedo works and reads approx 4890 miles. I do...

What engine oil do you recommend for a stock 73 CT70. Thanks, Fran

Hello, I just picked up a used carb and the small brass tube on the air inlet side is damaged, I had to open it up with a super small phillips screwdriver. It is opened up to normal size, but it is shorter than it should be, by 1/2,. Any ideas if this will effect it? I know carbs are sensitive...

:47: I just broke my carb (damn) I was removing the bowl and the support leg broke off???? I barely put any pressure on it. Oh well I need a stock ct70 carb, HHHHHEEEEELLLLLPPPPPP Please. Cell 413 657-3415 I have paypal Thanks, Fran

Good afternoon y'all My 73 CT70 timimg chain is waaayyy loose, i brought the adjuster all the way in and it had no effect?? I assume i need to replace the timing chain. I hope I dont have to split the case. Any info is appreciated. Thank, Fran

Hello, I have a nice all stock and original 1973 CT70. I unfortunately need to sell for XMAS $ :( It is orange in real nice cond, but has a few minor discrepancies, 1-frame paint has the usual scuffs, 2- the plastic covering for the exposed wiring harness in fragile and cracking off, wires...

Howdy Y'all I am putting the top end back togeather and I need to time it, I have the flywheel marks ligned up but I don't know what to lign up on the Cam and Sprocket? Please help, I need to go for a ride

I need a Left side engine cover,(magneto cover) front fork boots, seat cover. Thanks, Fran

I just want to pass along a soon to come Yamaha BW200. I am semi-restoring this, frame completely re-painted, wheels painted, crome polished, all bearing replaced or comfirmed they are ok. This thing is so much fun to ride. It should be done next sunday, and I will have plenty of pics...

I have some left over parts that are just hanging around, take a look and let me know what you need. Headlight and blinkers are 12v Hub is in great cond Let me know what you need. Cell (413) 657-3415 f.hoban@comcast.net Thanks, Fran

Hello, I have a 73 ct70 I just finished building, tons of new parts, looks real nice, has a brand new lifan 107cc engine, 20mm carb. It does not have headlight or taillight, I have a full 12v harness . I will have plenty of pics available. NEWPARTS: Tires, tubes, wheel bearings...

I ahve a sheng wey carb with th following marking 50Y 6c04 1216 0790 PCKE P10 Any idea what size this is?? Thanks, Fran

I got these two fenders with my 73 CT70 and thay do not fit, any idea what model they fit?? they are for sale or possible trade for a set that will fit my bike. They are brand new in perfect condition. :39: Thanks, Fran

I need a front and Back fenders for my 73 ct, also a taillight assy. Thanks, Fran

I need a carb for my Lifan 110cc engine, I have a stock CT70 Carb but I know it will need some jetting, If you have a 20mm carb I am looking for one. Thanks, Fran

:26: Howdy, I am just about to finish the assembly of my CT70 with a Lifan 110cc motor, I have the stock CT70 carb, but I am sure it will need much bigger jets, any recommendations on the correct jetting or a new carb I should get, I am thinking a 20mm. Anyone been through this before...

I have a set of fork tubes from MYTRAILBUDDY.COM, I Have read I can resize my original triple tree, I am looking for anyone who has done this, is this a machine shop resize or something I can do?? :39:

I am looking for a few parts for my 73 ct70: Handlebar mount with knobs Headlight assy, I need everything to include fork covers to mount headlight speedometer taillight assy Footpeg assy for a Lifan 110cc brake cables throttle cable carb cover and slide. f.hoban@comcast.net 413 657-3415...