Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Donations
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Honda Z50 Forums
General
Honda Z50m - Tune up
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="power6994" data-source="post: 190276" data-attributes="member: 6883"><p>Hey guys,</p><p></p><p>I have a z50m which was always really hard to start. Compression felt a little low and came to 105psi when tested so it might be a bit more taking into account the length of the guage hose. </p><p></p><p>My original plan was to tear down the motor, measure everything and replace what was needed. Just before pulling the motor out I decided to just try and start the bike. </p><p></p><p>After a lot of playing around I couldn't get the bike to start but I know I had gotten it to start before so something wasn't right. </p><p></p><p>I thought I would start with the carb. Opening the air filter housing revealed no filter at all. An order to Jaimie had one on the way. Maybe it being too lean was making it hard to start even with the choke. After installing the filter no real difference occurred. </p><p></p><p>Off the carb comes. I spotted a few tiny granules in the clear fuel hose so I disconnected it and flushed them out. When I took the carb off I pulled out both Jets. The emulsion tube looked nice and clean but the pilot jet I couldn't see any light. </p><p></p><p>So carefully removing the blockage and a little soak in degreaser they were back in. I also took a look at the float level while I was at it. </p><p></p><p>The float height measured 16mm but the manual spec is 18mm. I carefully adjusted it and checked a couple of times. </p><p></p><p>With the carb now reassembled and installed into the bike I rechecked the pilot screw putting it at 1-1/4 turns out. </p><p></p><p>Ignition switch on, fuel on, two kicks and it comes to life. Brilliant!! </p><p></p><p>The bike was revving quite high so I thought it a good opportunity to use a pulse tacho that I purchased off eBay. You can put it to the ignition lead and it tells you the rpm. 3100ish was the reading. </p><p></p><p>Back to the manual calls for 1500 +-100rpm. Winding down the slide adjusting screw on the carb let the bike sit nicely at 1500 without any fluctuations.</p><p></p><p>Now at this point the best test you can do is a slow and fast roll on to see if there is any stutter or movement when it returns to idle. Both tests went very well leading to one happy backyard mechanic. </p><p></p><p>The weekend presented a lot of rain so I didn't get to go for a little test ride so those results will have to wait. </p><p></p><p>Hope this info is helpful to someone. But it was nice to sort out a small problem and not have to start tearing down the motor in search of something bigger.</p></blockquote><p></p>
[QUOTE="power6994, post: 190276, member: 6883"] Hey guys, I have a z50m which was always really hard to start. Compression felt a little low and came to 105psi when tested so it might be a bit more taking into account the length of the guage hose. My original plan was to tear down the motor, measure everything and replace what was needed. Just before pulling the motor out I decided to just try and start the bike. After a lot of playing around I couldn't get the bike to start but I know I had gotten it to start before so something wasn't right. I thought I would start with the carb. Opening the air filter housing revealed no filter at all. An order to Jaimie had one on the way. Maybe it being too lean was making it hard to start even with the choke. After installing the filter no real difference occurred. Off the carb comes. I spotted a few tiny granules in the clear fuel hose so I disconnected it and flushed them out. When I took the carb off I pulled out both Jets. The emulsion tube looked nice and clean but the pilot jet I couldn't see any light. So carefully removing the blockage and a little soak in degreaser they were back in. I also took a look at the float level while I was at it. The float height measured 16mm but the manual spec is 18mm. I carefully adjusted it and checked a couple of times. With the carb now reassembled and installed into the bike I rechecked the pilot screw putting it at 1-1/4 turns out. Ignition switch on, fuel on, two kicks and it comes to life. Brilliant!! The bike was revving quite high so I thought it a good opportunity to use a pulse tacho that I purchased off eBay. You can put it to the ignition lead and it tells you the rpm. 3100ish was the reading. Back to the manual calls for 1500 +-100rpm. Winding down the slide adjusting screw on the carb let the bike sit nicely at 1500 without any fluctuations. Now at this point the best test you can do is a slow and fast roll on to see if there is any stutter or movement when it returns to idle. Both tests went very well leading to one happy backyard mechanic. The weekend presented a lot of rain so I didn't get to go for a little test ride so those results will have to wait. Hope this info is helpful to someone. But it was nice to sort out a small problem and not have to start tearing down the motor in search of something bigger. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Honda Z50 Forums
General
Honda Z50m - Tune up
Top